How to install remote for ceiling fan

Electrical Video 1 Electrical Wiring Tips? May 19, at pm. Paul says:. October 26, at pm. Dave Rongey says:. October 27, at am.

Viktor says:. December 21, at pm. STEVE says:. July 24, at am. Electrical Video 1 Electrical Wiring Tips. Helping You to Wire It Right! See the Electrical Wiring Video 2 Below:. Ceiling Fan Wiring and Connections with Video. Troubleshooting Light Switch Wiring. The Non-Contact Electrical Tester. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test. Very handy and easy to use. The Non-Contact Electrical Tester. Simply insert the end of the tester into an outlet, lamp socket, or hold the end of the tester against the wire you wish to test.

Very handy and easy to use. The Plug-In Outlet Tester. This is great to troubleshoot a problem with outlet circuit wiring, is also used by most inspectors to test for power and check the polarity of circuit wiring. It detects probable improper wiring conditions in standard VAC outlets Provides 6 probable wiring conditions that are quick and easy to read for ultimate efficiency Lights indicate if wiring is correct and indicator light chart is included Tests standard 3-wire outlets UL Listed Light indicates if wiring is incorrect, Very handy and easy to use.

The Wire Stripper and Wire Cutter. A wire stripping tool used to safely strip electrical wires. This handy tool has multiple uses: The wire gauges are shown on the side of the tool so you know which slot to use for stripping insulation. The end of the tool can be used to grip and bend wire which is handy for attaching wire onto the screw terminals of switches and outlets. Recent Testimonials I think your site offers the the clearest and best electrical information for homeowners I have ever seen on the net.

You have given me confidence to do my own projects which I never had before. This type of fan is also known as a flush-mount ceiling fan. In some cases, the installation, person needs to simply rotate the canopy.

After that, they get to see screws. Some other situations demand to remove the blade bracket. These are meant for holding the housing. Make sure you refer to the instructions for getting proper idea about what to do.

Now you need to place the receiver in its original spot. There should be wires on the ceiling. You need to make these wires lined up with the ones coming inside the sensor. However, there are also chances of needing to hang the receiver. In that case, you will use a zip tie to hand it from the bracket. After placing the receiver, you need to check if it fitted properly.

Then you can bring back the canopy or housing to install in its original spot. Make required adjustments to fit everything back to normal nicely. Before you actually disconnect the ceiling and fan wires that are existing, take a picture and this will work as a reference later on. Twist off the wire nuts which is also popular as wire connectors. I can wire the ceiling fan and just leave the red wire capped with a wire nut, but that leave a useless switch in the wall. The ceiling fan that was up before had a remote and the switches on the wall worked 1 switch had to be on in order for the remote to work, and the other controlled power to the fan.

How do I wire it back like this? I installed a hunter fan that utilizes the remote which had a different set up from the other poster.

The image below is how I did it and it works perfectly for utilizing both switches. One switch turns on the fan directly and the other provides power to the fan where you use the remote to adjust the speed. Important Note: The fan remembers your last setting so you might have to wire it per the manual and turn on the light first through the remote.

Now when one switch is on, the remote will control the light. The other switch will turn the fan on and off. You'll end up with something like this. This way the remote module will control the fan when the switch is in the ON position , and the other switch will control the light. This answer assumes the black wire controls the fan, while the blue controls the light kit on the fan. Check the documentation that came with the fixture, for proper wiring instructions.

For my switches to work, once I connected the blue wires for the lights together, I also had to connect those two blue wires to the black wire coming from the ceiling in order for the light to have power. This is a very helpful site. One wall switch powers entire fan. Make sure fan is on by pulling chain. Remote control now controls fan speeds and the light!

I did this last night at my condo. The fan is a Hunter remote, no chains. I wanted to be able to change the fan direction and speed, so I had to use the remote for that.

I wanted the light to be controlled from 2 3 pole switches.