Sony cdx gt 500 manual

If you have any questions or problems concerning your unit that are not covered in this manual, consult your nearest Sony dealer. Maintenance Replacing the lithium battery of the card remote commander Under normal conditions, the battery will last approximately 1 year. Page Removing The Unit If the fuse blows again after replacement, there may be an internal malfunction.

In such a case, consult your nearest Sony dealer. Cleaning the connectors The unit may not function properly if the connectors between the unit and the front panel are not clean. Note This unit cannot be connected to a digital preamplifier or an equalizer which is Sony BUS system compatible.

Design and specifications are subject to change without notice. Page 16 The contents of the memory have been erased. Stored stations and correct time are erased. If these solutions do not help improve the situation, consult your nearest Sony dealer. If you take the unit to be repaired because of CD playback trouble, bring the disc that was used at the time the problem began.

Reset the unit. Note: Stored data may be erased. Please contact U. Print page 1 Print document 36 pages. Rename the bookmark. Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.

Unleaded solder has the following characteristics. Ordinary soldering irons can be used but the iron tip has to be applied to the solder joint for a slightly longer time. Caution: The printed pattern copper foil may peel away if the heated tip is applied for too long, so be careful! Unleaded solder is more viscous sticky, less prone to flow than ordinary solder so use caution not to let solder bridges occur such as on IC pins, etc. It is best to use only unleaded solder but unleaded solder may also be added to ordinary solder.

When repairing or servicing this set, connect the jig extension cable as shown below. Location of controls and basic operations Sub FL Panel Assy CD Mechanism Block Main Board Chassis T Sub Assy Roller Arm Assy Chassis OP Assy Setting the clock The clock uses a hour digital indication.

The setup display appears. The hour indication is selected. To move the digital indication, press DSPL. The setup is complete and the clock starts. With the card remote commander In step 4, to set the hour and minute, press M or m.

Detaching the front panel You can detach the front panel of this unit to prevent theft. Caution alarm If you turn the ignition switch to the OFF position without detaching the front panel, the caution alarm will sound for a few seconds. The unit is turned off. The front panel is flipped down. Attaching the front panel Place the hole A of the front panel onto the spindle B on the unit, then lightly push the left side in.

Playback starts automatically. The disc is ejected. Note Do not put anything on the inner surface of the front panel. Radio: To tune in stations automatically press ; find a station manually press and hold. To cancel, press again. Radio: To receive stored stations press ; store stations press and hold.

S Z eject button 5 To eject the disc. T Disc slot 5 To insert the disc. Note If the unit is turned off and the display disappears, it cannot be operated with the card remote commander unless SOURCE on the unit is pressed, or a disc is inserted to activate the unit first.

Tip Displayed items will differ, depending on the disc type, recorded format and settings. Select To play Repeat Track track repeatedly. Shuffle Disc disc in random order. The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored.

The number button indication appears in the display. Note If you try to store another station on the same number button, the previously stored station will be replaced. Receiving the stored stations 1 Select the band, then press a number button 1 to 6.

Other functions Changing the sound settings Adjusting the sound characteristics You can adjust the balance, fader, and subwoofer volume. Tip Other equalizer types are also adjustable. Adjusting setup items — SET 1 Press and hold the select button. Note Displayed items will differ, depending on the source and setting. Info Information To display the items depending on the source, etc.

Dimmer To change the brightness of the display. Rotary commander RM-X4S Attaching the label Attach the indication label depending on how you mount the rotary commander. Changing the operative direction The operative direction of the controls is factoryset as shown below.